REPARAR DREAMBOX
JTAG + BOOTLOADER / HYPERTERMINAL
Si vuestra DM500S ya no arranca, si por algun motivo ha petado...
Pues nada ya he sacado los boots de arranque de las DM500S tanto las del sintonizador ALPS, como las del PHILIPS que es v1.
LOS RANGOS
0x00000000-0x00600000 : "DreamBOX cramfs+squashfs"
0x00600000-0x007c0000 : "DreamBOX jffs2"
0x007c0000-0x00800000 : "DreamBOX OpenBIOS"
0x00000000-0x007c0000 : "DreamBOX (w/o bootloader)"
0x00000000-0x00800000 : "DreamBOX (w/ bootloader)"
0x00120000-0x00600000 : "DreamBOX SquashedFS"
0x00000000-0x00120000 : "DreamBOX Cramfs"
http://www.**********.com/forum/manualdm/files/img_377.jpg
Milix
Aqui os pongo otro Jtag valido para todas las dream, como no lleva ningún integrado tampoco necesita corriente. Logicamente ademas de hacer el cable tendreis que poner un conector de 16 pins que irian en la foto que ha posteado el compi Manias.
http://www.**********.com/forum/manualdm/files/img_379.gif
Las conexiones son estas:
http://www.**********.com/forum/manualdm/files/img_382.jpg
Se necesita un pequeño programita para grabar el Boot bajo:
Windows / Linux / MacOsX
Aqui os dejo unas fotos de la version de windows.
http://www.**********.com/forum/manualdm/files/img_383.jpg
Si ocurre algun error, veriamos una pantalla como esta.
http://www.**********.com/forum/manualdm/files/img_384.jpg
Quirino18
En este caso el DreamUp tiene que trabajar, o puedes utilizar Hyperterminal que es igual a DreamUp.
La DM500S tiene que estar desconectada de la alimentacion.
Abrimos el HyperTerminal de Windows:
Inicio => Programas => Accesorios => Comunicaciones => HyperTerminal.
http://www.**********.com/forum/manualdm/files/img_385.jpg
http://www.**********.com/forum/manualdm/files/img_386.jpg
En los Settings the Hyperterminal tienes que seleccionar el puerto correcto y el modem a utilizar en este caso es ZMODEM guarda.
http://www.**********.com/forum/manualdm/files/img_387.jpg
http://www.**********.com/forum/manualdm/files/img_388.jpg
Presiona conectar en el HyperTerminal y conecta la alimentacion de la DM500S.
Veras como sale un mansaje... DREAMBOX 500S ETC. (esto significa que si tiene respuesta).
001 Disabled Application in Flash [FLASH]
002 Disabled Ethernet [ENET]
local=0.0.0.0 remote=255.255.255.255 hwaddr=000934208f53
003 Enabled Serial Port 1 [S1]
Baud = 9600
----------------------------
Automatic Boot: Enabled
----------------------------
1 - Toggle Power-On Tests.
2 - Change a Boot Device.
3 - Change IP Addresses.
4 - Ping test.
5 - Change Baud Rate for S1 Boot.
D - Display Configuration.
0 - Exit Menu and Boot Application.
->0
Installed RAM: 48 MB
System RAM check complete.
Booting from [S1] Serial Port 1...
PLEASE NOTE: You must now...
a. Exit from terminal emulation mode.
b. Modify the baud rate of your host session to 9600.
c. Transmit a file to the target using kermit.
d. Reset the host baud rate to 9600.
e. Reenter terminal emulation mode.
Si obtienes respuesta de la DM500S es por que si esta comunicando ! ! !
Presiona Transferir => Enviar Archivo, en el HyperTerminal y selecciona la imagen a mandar, asegurate que no este comprimida y que sea una imagen con extension *.img por ejemplo: dm500_factory.img
http://www.**********.com/forum/manualdm/files/img_389.jpg
Presiona Send y comenzara a mandar igual que DreamUp.
http://www.**********.com/forum/manualdm/files/img_390.jpg
http://www.**********.com/forum/manualdm/files/img_391.jpg
Recuerda que si habres HyperTerminal y la DM500S esta conectada no la detectara ! ! !
Manual DreamBox 500S v4.9