Resultados 1 al 2 de 2






ayuda boot problema


Estás en el tema ayuda boot problema dentro del subforo 990 CR HD PVR Spark LX en LonasDigital. ¡Hola Por favor, ayuda hay carreras en spark & enigma2 Spark : ok+power+up+ok = err Enigma2 : ok+power+down+ok = err...



Este tema tuvo 680 Visitas y 1 Respuestas

Actualmente hay 1 usuarios viendo este tema. (0 miembros y 1 visitantes)

  1. #1
    Avatar de pop1234

    pop1234 ha iniciado este hilo.
    pop1234 está desconectado
    Título:  Amigo de Lonas Rango:  Amigo de Lonas
    Fecha de ingreso
    Nov-2012
    Nacionalidad
    Francia
    Temas
    14
    Mensajes
    39


    ¡Hola

    Por favor, ayuda

    hay carreras en spark & enigma2

    Spark : ok+power+up+ok = err

    Enigma2 : ok+power+down+ok = err

    Cuando juegas

    visualización boot

    hyper terminal
    Código:
    Board: STx7111-Mboard (MB618)  [32-bit mode]
    info: Disregarding any EPLD
    
    
    U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
    
    DRAM:  128 MiB
    NOR:     8 MiB
    NAND:  512 MiB
    In:    serial
    Out:   serial
    Err:   serial
    IdentID : 09 00 07 00 00 80 51 
    
    Hit ESC to stop autoboot:  5  4  3  2  1  0 
    ## Booting image at a0080000 ...
       Image Name:   Kernel-Ramdisk-Image
       Image Type:   SuperH Linux Multi-File Image (gzip compressed)
       Data Size:    5867343 Bytes =   5.6 MiB
       Load Address: 80800000
       Entry Point:  80801000
       Contents:
       Image 0:  2970211 Bytes =   2.8 MiB
       Image 1:  2897119 Bytes =   2.8 MiB
       Verifying Checksum ... OK
       Uncompressing Multi-File Image ... OK
    found phy at addres = 1
    stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
    stb_id = 907008051
       Loading Ramdisk to 80d3c000, length 002c34df ... OK
    
    Starting kernel      nwhwconf=device:eth0,hwaddr:24:00:07:00:80:51  Manufacture=Spark-Project STB_ID=09:00:07:00:00:80:51 - 0x0053d000 -  2897119 ...
    Cuando se pasa uboot

    visualización err

    hyper terminal
    Código:
    xyzModem - CRC mode, 2(SOH)/512(STX)/0(CAN) packets, 2 retries
    ## Total Size      = 0x00080000 = 524288 Bytes
    Usage:
    protect - enable or disable FLASH write protection
    
    Usage:
    erase   - erase FLASH memory
    
    Usage:
    cp      - memory copy
    
    Usage:
    protect - enable or disable FLASH write protection
    menu+power ( printenv in hyper terminal )

    hyper terminal
    Código:
    Board: STx7111-Mboard (MB618)  [32-bit mode]
    info: Disregarding any EPLD
    
    
    U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
    
    RAM:  128 MiB
    NOR:     8 MiB
    NAND:  512 MiB
    In:    serial
    Out:   serial
    Err:   serial
    IdentID : 09 00 07 00 00 80 51
    Hit ESC to stop autoboot:  5
    MB618> printenv
    bootdelay=5
    baudrate=115200
    bootcmd=bootm  0xa0080000
    boot_system=spark
    kernel_name=spark/mImage
    userfs_len=17800000
    tftp_kernel_name=mImage
    tftp_userfs_name=userfsub.img
    userfs_name=spark/userfsub.img
    stdin=serial
    stdout=serial
    stderr=serial
    
    Environment size: 243/131068 bytes
    MB618>




    Citar Citar  




  2. #2
    Avatar de pop1234

    pop1234 ha iniciado este hilo.
    pop1234 está desconectado
    Título:  Amigo de Lonas Rango:  Amigo de Lonas
    Fecha de ingreso
    Nov-2012
    Nacionalidad
    Francia
    Temas
    14
    Mensajes
    39


    Thank you


    I've been solving the problem


    That way

    hyper terminal

    Código:
    ### for GM990Reloaded ###################################
    ac off
    ac on + hold menu-button
    now you can press in your terminalprogram "3"-exit 
    and you are on prompt:
    mb618>
    #########################################################
    ### fix args by comcable ################################
    #########################################################
    setenv ethaddr '00:80:E1:12:06:38'
    setenv bootdelay 3
    setenv baudrate 115200
    setenv board mb618
    setenv monitor_base '0xA0000000'
    setenv monitor_len '0x00080000'
    setenv monitor_sec '0xa0000000    0xa007ffff'
    setenv load_addr '0x80000000'
    setenv unprot 'protect off $monitor_sec'
    setenv update 'protect off $monitor_sec;erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec'
    setenv HOSTNAME LINUX7109
    setenv ipaddr '192.168.40.63'
    setenv netmask '255.255.255.0'
    setenv gatewayip '192.168.3.1'
    setenv serverip '192.168.40.19'
    setenv kernel_base_spark '0xa0080000 '
    setenv kernel_base_enigma2 '0x18000000'
    setenv kernel_sec 'a0080000 a077ffff '
    setenv kernel_len '0x00700000'
    setenv update_kernel 'protect off  a0080000 a077ffff ;erase  a0080000 a077ffff ;cp.b 0x80000000 0xa0080000  0x00700000 ;protect on  a0080000 a077ffff '
    setenv rootfs_base '0xa0800000'
    setenv rootfs_sec 'a0800000 a1ffffff'
    setenv menucmd update
    setenv tftp_kernel_name_spark mImage
    setenv tftp_kernel_name_enigma2 uImage
    setenv tftp_userfs_name_spark 'userfsub.img'
    setenv tftp_userfs_name_enigma2 'e2jffs2.img'
    setenv kernel_name_spark 'spark/mImage'
    setenv kernel_name_enigma2 'enigma2/uImage'
    setenv userfs_name_spark 'spark/userfsub.img'
    setenv userfs_name_enigma2 'enigma2/e2jffs2.img'
    setenv userfs_base_spark 800000
    setenv userfs_base_enigma2 18800000
    setenv userfs_len_spark 17800000
    setenv userfs_len_enigma2 7700000
    setenv kernelnfspath '192.168.40.19:/opt/target'
    setenv rootfs_name UserFS
    setenv rootfsnfspath '192.168.40.19:/home/d22cj/workspace/target'
    setenv uboot_name 'u-boot.bin'
    setenv ubootnfspath '192.168.40.19:/home/d22cj/workspace/target'
    setenv bootfromnfs 'nfs a4000000 $kernelnfspath/$kernel_name;bootm a4000000'
    
    setenv bootargs_nfs 'console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 stmmaceth=msglvl:0,phyaddr:1:watchdog:5000 root=/dev/nfs nfsroot=192.168.40.19:/opt/target,nfsvers=2,rsize=4096,wsize=8192,tcp rw ip=192.168.40.61:192.168.40.19:192.168.3.1:255.255.0.0:LINUX7109:eth0:off bigphysarea=4000'
    
    setenv bootargs_flash 'console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'
    
    setenv bootargs_spark 'console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'
    
    setenv magic_version '1.7'
    setenv filesize '203CA88'
    setenv fuseburned true
    setenv stdin serial
    setenv stdout serial
    setenv stderr serial
    
    setenv bootargs_enigma2 'console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000'
    
    setenv bootargs 'console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:lh:eth0:off stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000'
    
    setenv bootcmd bootm  '0xa0080000'
    setenv boot_system spark
    setenv userfs_base '800000'
    setenv userfs_len '17800000'
    setenv kernel_base '0xa0080000 '
    setenv kernel_name 'spark/mImage'
    setenv userfs_name 'spark/userfsub.img'
    setenv tftp_kernel_name mImage
    setenv tftp_userfs_name 'userfsub.img'
    
    ### before doing saveenv check via "print" if all correct!!! ####
    saveenv
    
    #############################################
    ### end #####################################
    
    now you turn ac off
    ac on and orig should bootup again
    if orig not booting you must flash rescue-pack1.2.09 again from here(watch readme how to flash):
    http://kathif.vs120005.hl-users.com/filebase_entry.php?entryid=374&sid=





    Citar Citar  

Subir